Hi Folks,
So over in Step 1, we created our lab systems, and installed the roles we needed onto each server. We also configured the domain and joined our Hyper-V and SCOM hosts to it.

Now we’re going to create the iSCSI target on the domain controller, and create the cluster on the Hyper-V hosts.

Firstly, we need to start by configuring the iSCSI target. I’d use a dedicated hard disk for this, so add a second disk to your VM (of at least 60GB), once that’s done, open Server Manager on the DC.

Navigate through “File and Storage Services” then “Disks” under “Volumes”. You should have a disk with ID 1, which has an unknown partition, or may not even be initialised. Create a new volume on the disk, which will mark the disk with the GPT info and create a partition. Once complete, click Close.

On the left of Server Manager, now click “iSCSI”. You should see something similar to this:

iSCSI-blank

Click on “To Create an iSCSI virtual disk, start the New iSCSI Virtual Disk Wizard”. Choose your newly created volume:

iscsi-1

Give your iSCSI disk a name, this will be used for the Hyper-V cluster, for any quorum requirements. Make it a 5GB disk, and if you want to save some disk space, choose “Dynamically Expanding”. You’ll need to create a new iSCSI target, so choose this option and click next. GIve your target a name (mine’s “iSCSI-Target”) and click next. You’ll need to add some initiators, so click Add, and add them by IP. These IP’s will be those you added to your Hyper-V hosts. You do this by choosing “Enter a value for the selected type” and choosing “IP Address”:

iscsi-init

Enable CHAP auth if you want to, but I won’t be, it’s only for a lab. Once complete, click Tasks, then “New iSCSI Virtual Disk”. Run through the wizard again, this time making a 50GB disk. This will be used to store your VM’s. This time, you can choose the existing iSCSI target. You’ll end up with something like this:

iSCSI-end

This gets us to the point of iSCSI configuration completed. It’s time to setup the cluster…

We’ll need to add the Failover Clustering feature to the Hyper-V hosts, and the management tools to the DC. If you add the two Hyper-V hosts into Server Manager on the DC, then you can do all of this from one place… much easier!

Under “All Servers” right click on one of your Hyper-V hosts, and choose “Add Roles or Features”. Click next until you reach the features page. Check the box for “Failover Clustering” and click next, keep going and start the install.  Do the same for the second Hyper-V host. Because I want my Hyper-V hosts to be “Server Core” at the end, I’m also going to install the Failover Cluster feature tools onto the DC. This can be done in the same way, but choosing the tools under “Remote Server Admin Tools” then “Feature Admin Tools” in the “Add Roles and Features” wizard.

On one of the servers, open the Failover Cluster Manager tool (in the tools menu in Server Manager). Choose “Create Cluster”. Add the two Hyper-V hosts into the cluster wizard:

Cluster-Hosts

Allow the tool to run the cluster tests… if any failures appear, resolve them first. After that you’ll need to enter a Cluster Name and IP Address. The name needs to be less than 15 characters for NetBIOS purposes. Do that and click next to create the cluster.

Next, configure your iSCSI initiator, and use the quick connect option, specifying the IP of the DC. It should connect, and present the 2 disks. Do this on both of the Hyper-V hosts. Mark them both as online in Server Manager, make a volume on this disk as “Q:” (for Quorum).  Next, you need to add this as a clustered volume.

Open up Failover Cluster Manager, and navigate to the Storage->Disks section. Click “Add Disk” and choose the 5GB drive. Once that’s done we need to setup the Quorum witness. Right click on your cluster, choose “More Actions” then “Configure Cluster Quorum Settings”. Click Next, then choose “Select the Quorum Witness”, and click next again. Choose “Configure a Disk Witness” and click next. Choose the 5GB disk, and click next. At the confirmation screen, check over the settings, and click next, then click finish. You should see the disk as “Disk Witness in Quorum” like this:

Quorum
Now we can add the 50GB disk as a cluster shared volume. Back in Server Manager, create a volume on the larger disk. I’ll be using V: for mine, as it’s for my VM’s. Go back to Failover Cluster Manager and choose “Add Disk” again. Choose the 50GB disk. Once that’s added, right click the disk and choose “Add to Cluster Shared Volumes”. This enables the disk for cluster use.

Enabling Live Migration… Still within Faillover Cluster Manager, choose the “Networks” node. Click “Live Migration Settings” and choose the LAN connection for Live Migration to use. I segregated this with my iSCSI traffic (by using a second network card purely for iSCSI) and wanted to make sure that Live Migration and iSCSI didn’t co-exist on the same LAN segment.

Next we need to add an external switch to each of the Hyper-V hosts. These need to have the same name. Open up Hyper-V Manager, and choose “Virtual Switch Manager”. Click to add a new virtual switch, and choose an external switch. Make sure you choose the NIC of the LAN NIC, and ensure you choose to “Allow management operating system to share this network adapter”. Click OK, and then click Yes to the warning. Complete the exact same actions on the second host, remembering to give them the exact same name.

That’s it! Cluster is built, Hyper-V is ready to run a VM…

Last piece of Part 2 then… removing the GUI from the Hyper-V hosts. This is something new to 2012 Server, and can be done via Powershell, or via the “Remove Roles and Features” wizard in Server Manager. Run through the wizard, selecting the host until you find the Features page. Uncheck “Graphical Management Tools and Infrastructure” and “Server Graphical Shell”. Removing just the latter will still give you a minimal graphical interface, with no Internet Explorer, or File Explorer amongst other items. Removing the first will put the server back to “Server Core” mode. NOTE: Removing the first will remove any additional RSAT tools you’ve installed (such as Hyper-V Manager and Failover Cluster Manager). It will NOT stop these items from working, just removes the consoles for local admin of those roles. It will also remove the Windows PowerShell ISE tool.

Over to part 3 for adding a VM and testing failover… and then part 4 will contain the installation for System Center 2012 R2… both coming soon!

Tags: , , , , , , , , , , , , , , , ,

Categories: Hyper-V ,Microsoft ,Server 2012 R2


2 Responses to “Creating a Windows Server 2012 R2 Preview Hyper-V Cluster Lab – Part 2 (Clustering)”

  1. Hey!Do you use Twitter? I’d like to follow you if that would
    be ok. I’m definitely enjoying your blog aand look forward to new updates.

Leave a Reply



%d bloggers like this: